Kitec plumbing lawsuit

What is the problem with Kitec plumbing?

Industry professionals believe that homes and condominiums with Kitec plumbing and fittings will experience premature pipe failure, and failure rates will increase over time. The pipes may not just leak but burst, with potential for flooding. The only complete solution is to replace Kitec plumbing with copper pipes .

When was kitec plumbing discontinued?

However, in 2005, the manufacturers of kitec piping recalled the product claiming that it had failed on the feature it was marketed for- resistance to corrosion. The kitec had accelerated corrosion rate. As a result, they discontinued its production.

How long does kitec plumbing last?

10 years

Should you replace Kitec plumbing?

Depending on the water chemistry in your area ( Kitec pipes tend to deteriorate faster in some areas) or how hot the water is from your water heater, you could be faced with frequent and costly repairs. Unfortunately, there is no proven way to maintain Kitec pipes so that they do not rupture.

Does homeowners cover kitec plumbing?

Yes. If the problem is with KITEC pipes or fittings you should have a licensed plumber look at your pipes and replace the defective pipes or fittings. You should also file a Claim Form in order to be eligible to receive payment under the settlement.

How do you tell if I have Kitec plumbing?

How do I know if I have Kitec Plumbing ? If you’re curious if your condo might have kitec , look at the condo corporation number. If the number is between 1200 and 1900, it may contain kitec , as buildings are registered by date of completion.

You might be interested:  Backflow plumbing

Why is PEX plumbing bad?

PEX failures Piping fails when the pipes are exposed to chlorine that is within the water, exposure to direct sunlight before its installation. Furthermore PEX pipe is vulnerable when it comes in contact with such solutions as petroleum products and oxygen. It can leach toxic chemicals from pipe material also.

Is IPEX the same as kitec?

KITEC is a brand of water supply pipe and brass fitting which was manufactured by Canadian pipe manufacturer IPEX . The brass fittings were produced from 1995 until 2005, when IPEX issued a recall on the fittings due to failures.

How much does it cost to replace Kitec plumbing in Toronto?

Replacing Kitec can cost between $4000 and $14,000 and the owner is responsible for the cost (even in condos).

How much does it cost to replace Kitec plumbing?

How Much Does Kitec Plumbing Cost to Replace? Depending on the extent of the Kitec plumbing in your home, it can cost anywhere from $5,000 to $15,000 .

How do you cut kitec pipe?

All sizes of Kitec can be cut using a pair of plastic-and-metal shears that slice the pipe more effectively than you’d think possible at first glance. A hand-held reamer removes burrs on the inside of the pipe that might otherwise damage the O-rings on the connector fittings.

When was kitec plumbing used?

2000s

What is the best pipe to use for plumbing?

Copper pipes are popular for both hot and cold water pipes because they are heat resistant, resist corrosion, and have natural anti-microbial properties. They are more expensive than plastic pipe options. Average cost-per-foot for copper piping is between $2.50 and $3.50 compared with PEX , which is around $.

You might be interested:  Plumbing cartridge puller

Is PEX plumbing kitec?

Kitec ® is a brand of plastic piping used in hot and cold water supplies to plumbing fixtures, and in heating systems with boilers. It was made from 1995 to 2007. It is cross-linked polyethylene ( PEX ). PEX continues to be popular for both plumbing and heating systems in homes.

What are the disadvantages of PEX?

PEX Plumbing Disadvantages PEX may leach BPA and other toxic chemicals. PEX is extremely sensitive to UV light. PEX can be damaged by chemicals and pests. PEX can’t be installed in high heat areas. PEX is semi-permeable, which means liquid can enter the pipe.