Kitec plumbing disclosure

Do you have to disclose kitec plumbing?

If you are a Seller, be aware that the existence of Kitec Plumbing will impact your selling process and potentially your price. You should disclose this information to your Buyer to protect yourself from legal action down the road.

What is the issue with Kitec plumbing?

Industry professionals believe that homes and condominiums with Kitec plumbing and fittings will experience premature pipe failure, and failure rates will increase over time. The pipes may not just leak but burst, with potential for flooding. The only complete solution is to replace Kitec plumbing with copper pipes .

Does homeowners cover kitec plumbing?

Yes. If the problem is with KITEC pipes or fittings you should have a licensed plumber look at your pipes and replace the defective pipes or fittings. You should also file a Claim Form in order to be eligible to receive payment under the settlement.

When was kitec plumbing discontinued?

However, in 2005, the manufacturers of kitec piping recalled the product claiming that it had failed on the feature it was marketed for- resistance to corrosion. The kitec had accelerated corrosion rate. As a result, they discontinued its production.

Is IPEX the same as kitec?

KITEC is a brand of water supply pipe and brass fitting which was manufactured by Canadian pipe manufacturer IPEX . The brass fittings were produced from 1995 until 2005, when IPEX issued a recall on the fittings due to failures.

How long does kitec last?

approximately 10 years

How much does it cost to replace Kitec plumbing?

How Much Does Kitec Plumbing Cost to Replace? Depending on the extent of the Kitec plumbing in your home, it can cost anywhere from $5,000 to $15,000 .

You might be interested:  Kitec plumbing replacement cost

Why is PEX plumbing bad?

PEX failures Piping fails when the pipes are exposed to chlorine that is within the water, exposure to direct sunlight before its installation. Furthermore PEX pipe is vulnerable when it comes in contact with such solutions as petroleum products and oxygen. It can leach toxic chemicals from pipe material also.

What does kitec look like?

What does it look like ? Kitec Hot water and radiant heat lines will be orange/red piping and cold lines will be blue. Sometimes the pipes will even have Kitec printed on the pipes.

How do I know if my house has Kitec plumbing?

To be sure, your best bet is to check out in the area around the hot water tank or in the mechanical room where the pipe connects or exits the walls. You’ll also be able to find them in bathrooms as well, under the sinks. Fittings are stamped clearly with Kitec or KTC.

How much does it cost to replace Kitec plumbing in Toronto?

Replacing Kitec can cost between $4000 and $14,000 and the owner is responsible for the cost (even in condos).

How much does Repiping a house cost?

While the costs to repipe a house varies with each project and across the United States, it will usually cost $600 to $2,000 to repipe a single feature (toilet, tub, etc.) and you can expect to pay anywhere from $4,000 to $15,000 for a complete piping system replacement.

When was kitec plumbing used?

2000s

What is kitec plumbing?

Kitec plumbing consists of flexible aluminum pipe between an inner and outer layer of plastic pipe (PEX pipe ) with brass fittings. Marketed as a cheaper and easy-to-install alternative to copper piping , Kitec was sold between 1995 and 2007 for potable water, in-floor, and hot-water baseboard heating systems.

You might be interested:  Estimate plumbing cost new construction

What is PEX plumbing?

About PEX Piping for Plumbing : PEX stands for cross-linked polyethylene. It is a type of plastic tubing made from high-density polyethylene. It is used for radiant floor heat tubing and for water supply. PEX has a lot of advantages over copper piping , such as: It is far less expensive as a raw material.